Feeds:
Posts
Comments

Archive for the ‘Gadgets’ Category

Barbecue Tech

So, I’d owned a Weber barrel-style smoker for years. It was great, but it just didn’t have enough grill space for me to cook for a crowd.  So, my lovely wife got me an offset smoker with a larger grill:

And thus, it was decreed that our house would host the family Thanksgiving this year. Now, I could have sat around and tended the smoker for 8 hours like our barbecue ancestors would have, but we have the benefit of modern technology… so a few modifications were in order:

DSC_0002

The first modifications were some simple ones to improve airflow — namely, extending the chimney down to grill level and sealing some of the air gaps with JB weld.

The next problem I looked had to do with the byproduct of charcoal cooking — the ash. The side fire box comes  with a pull-out ash tray, but the problem is that the grill which holds the coals sits on top of the ash tray — so there’s no way to remove ashes while you’re cooking. (Also, the metal in the OEM charcoal grill had warped due to heat after a single cook.) So, I bought a replacement grill from Lowe’s and had my brother-in-law cut it down to size (about 17″x30″). Now, it sits nicely above the ash tray, and I can dump the ash while cooking, without affecting the coals:

DSC_0006

You can also see in that picture part of the electronics setup: the stoking fan, a 10cfm fan which can be turned on and off electronically to control the rate at which the charcoal burns (and thus, the smoker temperature). Normal smokers depend completely on the chimney effect, which works well, but the only way to control airflow is by adjusting the intake and outflow openings, which is inexact and can also be greatly affected by wind conditions.

The fan is controlled by the brains of the operation:
DSC_0008

This is a Stoker, from Rock’s Barbque. Based on a TINI board, it has 5 inputs and outputs for temperature sensors and fans, as well as the user interface you can see here for controlling the fans and configuring temperature setpoints. It also has an ethernet port, which I have connected to a wireless bridge (you can see it hiding above the controller in the picture above) so that it can connect both to my local network and the Internet as well.

Through the buttons on the controller itself, or the built-in web interface, you can see what the current temperature readings are, and also control it:
smoker

Here, I have Sensors 1 and 3 set up in different locations in the smoker, pulling the ambient (‘cooking’) temperature. Sensor 1 is controlling Blower 1 (the fan), and if the temperature goes past the target, the fan will turn on or off (some hysteresis is introduced to keep the fan from turning on and off rapidly when near the target temp).

Now, you might think, temperature over time… that would be a great thing to see on a graph. With the assistance of AmirM’s StokerLog, we can! Here’s the chart from my Thanksgiving turkey cook:
smokerchart

As you can see, I started the smoker around 9:30, added the bird at around 10, and proceeded to cook it for about 5 hours. Here, the purple line is the temperature according to a temperature probe inserted into the deepest part of the breast, and the blue line moving at right angles is the fan output, either on or off.

One of the best things about the smoker setup is that I no longer have to watch it like a nervous mother hen — I wasn’t even at the house between 10:30 and 12, but I never worried because I’d forwarded a port on my router to the stoker’s web interface and could check on it as much as I wanted.

How did the turkey turn out? Awesomely moist, and with a great smoke flavor:
Turkey

Read Full Post »

Mavromatic points out Microsoft’s beta release of their mobile search app — and it’s very impressive. Mapping (with Google-map-esque panning and zooming), driving directions which can be overlaid on said map, POI (points-of-interest) location search, and perhaps most impressively: ability to update location based on GPS and live traffic updates for certain cities (unfortunately not including Dallas). Apart from the traffic updates, I could get all of this previously by running Mapopolis, but that was a >$100 investment to get what this app provides for free.

The interface is very easy to work with, and the installation process was a breeze, tons easier than getting mobile Google maps to run… which is not entirely Google’s fault, but the efforts I had to go through for to get Google’s app running and the resulting user experience (including slow map downloads, inexplicable freezes, and having to install an alternate VM) made for a painful installation compared to this one — download, auto-install and run. The interface seems very snappy as well, even though I’m only using it on EDGE. I only used the Windows Mobile version on my T-Mobile MDA, but they also have a J2ME version which should give this app a pretty wide audience.

One thing to be aware of for those on pay-per-byte plans: The app is making multiple network calls (especially when scrolling a map), so you might need to manage your costs appropriately.

Download and install (for J2ME or Windows Mobile) by going to http://wls.live.com/ on your mobile device.

Read Full Post »